Using a clay bar got a Q - Mustang Evolution

Go Back   Mustang Evolution > Ford Mustang | Wrenching, Care and General Topics > Mustang Audio & Video



Reply
 
Thread Tools Search this Thread
Please support our sponsors and let them know you heard about them here!
Old 08-16-2004, 02:15 PM   #1
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
Using a clay bar got a Q

I just want to strip down the paint to no protection and clay bar the whole thing and then put stuff back on it, I know black = feather scratches like crazy as far as showing up and will a clay bar remove these?

I have 2 clay bars a car brite given to me and a mothers clay bar i purchassed, I am going to use dawn detergent to clean the car off before i clay bar, should i use rubbing compound first? or will the clay bar remove some swirl marks? is mothers a good brand in clay bars?

thanks for any tips/help
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-16-2004, 02:49 PM   #2
Road Trip!
 
Join Date: Jun 2004
Posts: 321
Send a message via AIM to kaper232 Send a message via Yahoo to kaper232
All a clay bar does is remove paint contamination. Are you actually trying to get rid of swirls in the paint? Also, dawn and other household soaps arent recommended for using on your car.

Compound - Polish - Finish = 3 Step procedure for removing scratches and swirls

If you are wanting to remove scratches, a compound such as Menzerna Intensive Polish, Meguiar's Medallion Premium Paint Cleaner or 3M Fine Cut Compound should work. Compounding is normally done with a circular polisher or dual-action polisher.

Now to polishing.. Since compounding can leave the clearcoat a bit hazed. A polish such as Menzerna Final Polish, Meguiar's No. 9 Swirl Remover or 3M Perfect-It Swirl Mark Remover will work in this step.

For Finishing.. Use your favorite wax or sealer.

There are plenty of brands out there, I just named a few that will work.

Anymore questions, I will try to help...
kaper232 is offline   Reply With Quote
Old 08-16-2004, 03:26 PM   #3
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
well i have light feather scratches that every car has its just part of it they are barly noticable but having a black car.... you have to take extra care to keep them in check. I know dawn will remove all protection on the car thats why i am using it, it is the best at cutting off the wax/protection from the paint so you can get down to the paint with out having to go though the wax/protectant layers to clean the paint, I am stripping it all the way down to remove all protection then clay baring it to clean the paint, I was just wondering if the clay bar removed feather scratches or only cleaned the paint, i feel it only cleans the paint.

I will probably wash it with dawn to clean the car good/strip it down then rubbing compound it 1-2 good times with 3m perfect it II clear coat safe (the BEST compound out there does wonders, i have part number but not near bottle) then after that clay bar it really good and go back with my waterless car wash to protect it i would never wash the car with dawn or any kind of detergent like that and leave it thats just a bad idea. I hate washing cars in general with water, more hassel than its worth to many hard water spots... EVIL hard water spots lol, i have used the 3 step as you mentioned but i get better results with my dwg so i just use it, i may go over with the swirl remover but its probbaly not gonna be needed. Plus this will be out side for some parts... black is HORRIBLE in the sun... you can not wash a black car with normal tap water out side with no shade unless you really take your time.... the mr clean thing works good im sure since mineral deposits are what leaves the spots to begin with but i dont feel like buying one when i dont need it but maybe once every 3 years.

the car has never been waxed and is in mint shape its just 3 years old and i wanted to strip it down and take some time to remove swirl marks and clean the paint especially since i didnt when i got it new and rail dust and all that probably got on it. regardless of what you do feater scratches are gonna happen.... just have to keep them in check.

so mainly just wondering if the clay bar will remove swirl marks/feather scratches
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-16-2004, 03:39 PM   #4
Road Trip!
 
Join Date: Jun 2004
Posts: 321
Send a message via AIM to kaper232 Send a message via Yahoo to kaper232
OK, I am better understanding you now... You are correct, the clay bar isnt for removing swirls, blemishes, old wax etc... Just merely to clean the topcoat of contaminants.
kaper232 is offline   Reply With Quote
Old 08-16-2004, 03:59 PM   #5
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
ah ok, well thats good news and bad news.... good news is just that its not gonna be really abrasive... bad news is i have to spend more time on the car now my friend is gonna help me .... its still gonna take all day lol maybe we can start tonight and get to the compounding~ if i have enough left..... lol
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-16-2004, 05:01 PM   #6
Registered Member
Regular
 
Join Date: Apr 2004
Region: California
Posts: 4,272
dont use the dawn the clay bar will do all that by its self dawn will eat your clear coat.

just use alot of elbow grease with the clay bar, if you want to remove the feather scratches you can color sand with a wet 2000 grit sand paper but since the car is so new i would not reccomend it. just use the clay bar throw on 3m rubbing compound 3m glaze and your favorite wax but make sure you do all this in the shade.
STEVE is offline   Reply With Quote
Old 08-17-2004, 03:17 AM   #7
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
I cleaned the car off with dawn then compounded it then clay bared it (which seemed to do nothing... the car was smooth and the bar just slide around didnt pick up much... i guess my paint doesnt have much on it .... then i washed it again and finished up with my dwg and a oribtal buffer i have another coat of dwg and im done its looking great so far.
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-17-2004, 03:30 AM   #8
Road Trip!
 
Join Date: Jun 2004
Posts: 321
Send a message via AIM to kaper232 Send a message via Yahoo to kaper232
Cool, show pics when its finished!!
kaper232 is offline   Reply With Quote
Old 08-17-2004, 03:22 PM   #9
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
no digital camera but i did finish it today and it came out pretty good, it was hard to improve upon before... the clay bar didnt do jack squat maybe smoothed it a tad but it didnt pick up anything. ill try to get some pics. the little 20 buck buffer i got worked really nicly.
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-17-2004, 04:29 PM   #10
Registered Member
Regular
 
Join Date: Apr 2004
Region: California
Posts: 4,272
first you use the claybar then throw on the compound
STEVE is offline   Reply With Quote
Old 08-17-2004, 05:48 PM   #11
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
K ill remember that next time i just figured the compound may leave residue behind that the bar would remove, ill do it reverse next time but i dont think the car can get much slicker lol.
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-17-2004, 06:35 PM   #12
Registered Member
Regular
 
Join Date: Apr 2004
Region: California
Posts: 4,272
did you use glaze before the wax?
STEVE is offline   Reply With Quote
Old 08-17-2004, 10:07 PM   #13
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
I didnt wax
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-24-2004, 09:34 AM   #14
Registered Member
Regular
 
Warfire80's Avatar
 
Join Date: Feb 2004
Region: Illinois
Posts: 798
Send a message via MSN to Warfire80
go to www.zainobros.com, has all the info you need
__________________
2007 Honda Civic EX
2003 Dodge Ram Hemi 4x4

Quote:
by Lawrence Bell
Show me a man who cannot bother to do little things and I'll show you a man who cannot be trusted to do big things
Warfire80 is offline   Reply With Quote
Old 08-24-2004, 09:37 AM   #15
Registered Member
Regular
 
Warfire80's Avatar
 
Join Date: Feb 2004
Region: Illinois
Posts: 798
Send a message via MSN to Warfire80
some nice work from zaino....



__________________
2007 Honda Civic EX
2003 Dodge Ram Hemi 4x4

Quote:
by Lawrence Bell
Show me a man who cannot bother to do little things and I'll show you a man who cannot be trusted to do big things
Warfire80 is offline   Reply With Quote
Old 08-24-2004, 10:01 AM   #16
I liek gramer
Legacy
 
WhiteStang99's Avatar
 
Join Date: Jan 2004
Region: Florida
Posts: 8,537
Send a message via AIM to WhiteStang99
where did that drool smilie go!!!

:drool:

we used to have one.
WhiteStang99 is offline   Reply With Quote
Old 08-24-2004, 11:38 AM   #17
Legacy Member
Legacy
 
Fishers Stang's Avatar
 
Join Date: May 2003
Region: Indiana
Posts: 1,507
Send a message via AIM to Fishers Stang
dang it i missed this, hahaha I detail 10-12 cars a day.. i dont think you should use dish soad, BUT if thats all you have that will clean it really good, then use a small bit. Clay bar will only get out "tree sap, over spray, light tar, some fall out, fresh bird dropings, road film" this time of the year is when i start using it a lot do to the trees, and area I work/ live. when you look at your paint, here>
Quote:

2. What is the best way to restore gloss to a dulled painted surface?


Lack of gloss on a painted surface results from three factors:






  • Oxidation of the exterior paint layer
  • Scratches in the exterior paint layer
  • Lack of a protective coating on the exterior paint layer
Oxidation is the dulling of the painted surface that occurs when the sunís ultraviolet rays deplete the paintís natural oils and resins. Scratches prevent light from reflecting uniformly from the painted surface, which limits gloss. In order to restore gloss, oxidation and scratches must be removed.



Once the surface is free of oxidation and scratches (see Question #3) and any swirl marks caused during buffing are removed (see Question #4), a wax or paint sealant should be applied to protect the surface against further oxidation, and to intensify gloss.

and
Quote:
3. How do I safely remove scratches and oxidation from a painted surface?


To remove medium to heavy scratches and oxidation, you must buff the surface with a high speed buffer, cutting pad and buffing compound (For a complete listing of Car Brite compounds, See theCompounds section of the Products page of this website).



If only light scratches and oxidation are present, buffing with a mildly abrasive polish and polishing pad is recommended (See Question #4 for more information on polishing).

If the scratches and oxidation are sufficient, the compound used should be aggressive enough to correct the imperfections present but appropriate for the vehicleís paint system (conventional or basecoat/clearcoat). To identify your vehicleís paint system, use an applicator pad to hand apply a medium-duty compound to an inconspicuous spot on your rear bumper. If color comes off on the pad, youíre working with a conventional system. If not, you have a basecoat/clearcoat system.

The thickness of the exterior paint layer of conventional systems is 3 - 4 mils (1 mil = 1/1000 of an inch), while the thickness of the clearcoat layer is 1 - 1.5 mils. Therefore, you can use a much more aggressive product on a conventional finish than on a basecoat/clearcoat finish.

When compounding, the buffer should be run at no higher than 1800 - 2000 rpm, and either a wool or foam cutting pad may be used. Wool cutting pads tend to generate more heat than foam pads - increasing the amount of cut - and often leave more swirl marks.

If a paint thickness gauge is available, measure the total thickness of the surface you plan to buff. Then measure the thickness periodically as you buff, ensuring that you donít remove more than .5 mils of paint (especially from a clearcoat layer).

Select your compound accordingly, and buff the vehicleís painted surfaces per the following guidelines:




  • Ensure painted surface is cool before buffing
  • Apply a moderate amount of product to surface, and donít allow the product to dry on surface
  • Donít mix buffing products
  • Moisten pad before buffing (especially foam pads)
  • Buff slowly in shoulder width area, moving buffer side-to-side, length-wise with panel
  • Spur pad regularly with pad spur (either a wool or foam pad spur - never a screwdriver!)
  • Keep pad flat on surface, applying light even pressure
  • Bring buffer off painted surface before stopping
  • Wipe off residue with clean, soft cloth
This process is illustrated in greater detail in the Removing Scratches, Oxidation and Swirl Markssection of this website.







4. What are swirl marks, and how do I remove them?




Swirl marks are light, circular scratches in the painted surface often caused by buffing with a compound. As the compound cuts away the oxidized paint layer and reduces the depth of deep scratches by abrading away their "ridges", light scratches usually remain, especially on dark colors.



Fear not, for swirl marks can be safely and effectively buffed out with a high speed buffer, polishing pad and a polish (as can light scratches and oxidation not severe enough to warrant compounding). For a complete listing of Car Brite polishes, See thePolishes section of the Products page of this website.

A polish is a lotion containing mild abrasives and resins (usually silicone) that can be applied with a buffer or by hand. The abrasives remove swirl marks by abrading away their "ridges" in a manner similar to compounding, but with much less paint being removed.

The polishís resins fill any indentation in the paint too deep to be abraded out, and bond to the surface. By removing the "ridges" and filling any remaining indentations, the painted surface is leveled, which restores its gloss. The newly level surface reflects light in a uniform manner causing the eye to perceive a deep, rich shine.

In addition to providing "fill", the resins deflect the sunís ultraviolet rays (minimizing further oxidation) and magnify the gloss created by the newly level surface.

The durability of the bond between the resin and the painted surface will vary depending on the number and type of resins used. Silicone is the most common resin, and certain chemically-bonding silicones can last up to six months. Glycerin and mineral oil are also used, but arenít nearly as durable.

When polishing, buff at 2400 - 2800 rpm (the resins provide added lubrication which allow for higher buffer speeds), and utilize a lambswool, blended wool or foam polishing pad. Also, follow the buffing guidelines listed in Question #3.

This process is illustrated in greater detail in the Removing Scratches, Oxidation and Swirl Markssection of this website.





5. How often should I wax my vehicle, and what is the best method?




Waxing frequency depends on the type of wax or paint sealant you use, the climate you live in and the soap you use to wash your vehicle.



Before discussing these variables, we should review the terms "wax" and "paint sealant". Historically, a "wax" was a final finish product which contained natural waxes such as carnauba, while a "paint sealant" was a final finish product containing synthetic polymers such as silicone, glycerin and mineral oil. Waxes tended to bring out more shine, while paint sealants tended to last longer.

Today, however, the distinction between these products is not as pronounced. Many "waxes" contain synthetic polymers, while many "paint sealants" contain natural wax. Itís best to review the product label to determine shine and durability (For a complete listing of Car Brite waxes and paint sealants, See theWaxes and Paint Sealant section of the Products page of this website) .

Like polishes, waxes and paint sealants contain resins which bond to the painted surface forming a protective layer against sunlight and the elements. The strength of the bond will vary depending on the number and type of resins present and the condition of the painted surface.

Chemically-bonding silicones can last up to six months, while physically- bonding silicones, mineral oil, glycerin and natural or synthetic waxes last one to four months. It is critical to ensure that the paint is free of dirt, tar, grease, and other surface contaminants before applying your final finish product. Neither wax nor paint sealant will adhere to a dirty surface.

Climate affects the durability of waxes and paint sealants, as well. Harsh weather conditions such as rain, wind, snow (and the accompanying road salts) will break the bond between the resin and the painted surface much more quickly than will dry, mild conditions. Constant exposure to bright sunlight will also accelerate wax and sealant deterioration.

When washing a freshly-waxed surface, be sure to use a pH neutral car soap instead of a highly alkaline dish soap or household cleaner. The alkalis will strip the resins from the painted surface, lessening gloss and exposing the surface to the elements.

Car Briteís recommended procedure for applying a final finish product can be found in the Applying Wax or Paint Sealant section of this website.





6. How can I quickly remove surface contaminants without buffing?




Paint overspray, bugs, tree sap and other light surface contaminants can be quickly and easily removed with Car Briteís Brite Stik Gray (B080) and Brite Stik Purple (B081) Clay Bar.







7. What is a clay bar, and how is it used?




The Brite Stik (B080) and Brite Stik (B081) Clay Baris a blend of synthetic rubbers containing mild abrasives that removes light surface contaminants such as paint overspray, bugs and tree sap from painted, glass and chrome surfaces.



Car Briteís recommended procedure for using the clay bar is illustrated in the Surface Contaminant Removalsection of this website.

that was from a company that I use, but if you dont havea high speed buffer, then you can try with hand the rubbing compound, then any kind of wax. if ya need anything else hit me up on aim, ill try to find somemore info. here > me and dads stangs,

__________________
Charles
2006 F150 4x4 with the 5.4L V8
Fishers Stang is offline   Reply With Quote
Old 08-24-2004, 08:44 PM   #18
Road Trip!
 
Join Date: Jun 2004
Posts: 321
Send a message via AIM to kaper232 Send a message via Yahoo to kaper232
Jesus Fish... Write a novel next time!!! Car perv!!!
kaper232 is offline   Reply With Quote
Old 08-24-2004, 09:02 PM   #19
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
my paint was to clean for the clay bar to do anything it may have helped but there was nothing really for it to remove
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-24-2004, 09:59 PM   #20
Legacy Member
Legacy
 
Fishers Stang's Avatar
 
Join Date: May 2003
Region: Indiana
Posts: 1,507
Send a message via AIM to Fishers Stang
Quote:
Originally Posted by kaper232
Jesus Fish... Write a novel next time!!! Car perv!!!
well I am a full time detailer for a very large car dealership. we dont just wash the car, we bring it back to stock and then wash, clay, wet sand touch up, insides, engines, rims, wet sand scratches, and then buff out (high speed) and then wax. all in less then 3-4hrs per car. get paid good money for it also
__________________
Charles
2006 F150 4x4 with the 5.4L V8
Fishers Stang is offline   Reply With Quote
Old 08-25-2004, 10:51 AM   #21
Registered Member
Regular
 
Warfire80's Avatar
 
Join Date: Feb 2004
Region: Illinois
Posts: 798
Send a message via MSN to Warfire80
I think I would get so tired of doing everyone elses cars I wouldnt want to do mine.
__________________
2007 Honda Civic EX
2003 Dodge Ram Hemi 4x4

Quote:
by Lawrence Bell
Show me a man who cannot bother to do little things and I'll show you a man who cannot be trusted to do big things
Warfire80 is offline   Reply With Quote
Old 08-25-2004, 07:42 PM   #22
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
yea, but you as well as we all know on your own car you usually do a much better job than someone elses at least I tend to.
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 08-25-2004, 08:13 PM   #23
Legacy Member
Legacy
 
Fishers Stang's Avatar
 
Join Date: May 2003
Region: Indiana
Posts: 1,507
Send a message via AIM to Fishers Stang
Quote:
Originally Posted by SpectorV
yea, but you as well as we all know on your own car you usually do a much better job than someone elses at least I tend to.
yup...
__________________
Charles
2006 F150 4x4 with the 5.4L V8
Fishers Stang is offline   Reply With Quote
Old 08-25-2004, 11:35 PM   #24
Legacy Member
Legacy
 
Black95GT's Avatar
 
Join Date: Jul 2003
Region: New Jersey
Posts: 897
Send a message via AIM to Black95GT
I just clay bared my car, with the zanio kit im using, then I washed it. Tomorrow ill start polish and wax
__________________
-Jason
2003 DSG Cobra -2.2L KB, 60lbs Injectors, Single Blade TB, SCT2400 MAF, Kook's LT's, Kook's High-Flow Catted X-Pipe, Magnaflow CB, JLT RAI, MGW Short-Throw, H&R Race Springs, MM CC Plates, MM Bumpsteer, BF IRS Brace, BF Idlers, and AFS 18 Chrome Reps w/ R888s
Black95GT is offline   Reply With Quote
Reply

Lower Navigation
Go Back   Mustang Evolution > Ford Mustang | Wrenching, Care and General Topics > Mustang Audio & Video

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Clay bar upton7 General Mustang Discussion 8 08-27-2009 09:02 AM
so since this is the bar... MonteCitan The Bar 33 03-08-2007 11:30 AM
Meguiars Clay Bar + Meguiars NXT = awesome Thomas91169 Mustang Audio & Video 3 09-04-2006 11:28 PM
/bar/ Vs. /the-Bar/ 03redfire cobra The Bar 5 11-09-2005 10:35 AM
How to: Roll Bar (light bar install) cagedthought Mustang Audio & Video 12 11-02-2004 09:18 AM

» Like Us On Facebook



06:18 PM


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0

MustangEvolution.com is in no way associated with or endorsed by Ford Motor Company.