I Need Lots Of Stuff!!

[ridenmystang]

Diablo Programmer
K&N Cold Air Intake
Long Tube Headers
Lowering Spings/CC Plates

I really need to start focusing on my motor mods now since I have it just about how I want it to look Let me know what I should get.

[SpectorV]

I thought you were contemplating selling for a more "pimp" ride... lol

[ridenmystang]

Well I change my mind every day I mean Every Second hahaha

[SpectorV]

imagine that

[Herbstang]

Very Nice List !! Your car has come a long way and is looking real good .But how about a SCT chip Support the site sponors

[SpectorV]

lowering springs and cc plates will make it look TONS better and handle much better as well. How low do you want to go? Keep in mind more than 1.5 inches you start to run into issues~

[ridenmystang]

Guess what I got 4 my Bday yeasterday? Lowering Springs! Yeeeehhh! Now I need some cc plates. My Bf got them 4 me at summit, performance racing springs that lower 1.5"

[SpectorV]

buy maximum motorsport 4 bolt CC plates.

[ridenmystang]

What about these?

eBay Motors: UPR Mustang 94-04 Caster Camber Plates Shark Suspension (item 300022033344 end time Sep-03-06 18:38:28 PDT)

eBay Motors: UPR 94-04 Mustang 4-Bolt Caster Camber Plates Silver NR (item 250022874442 end time Sep-02-06 12:12:37 PDT)

[lowflyn]

If you are going to buy c/c plates, get 4 bolt, not 3 bolt. Take a little more to install but the range of adjustability is so much better. I still recommend mm c/c plates, but upr would work.

[SpectorV]

its just that 4 bolt cc plates adjustmore, its that Maximum Motorsport's brand 4 bolt CC plates adjust more. No other plate on the market (that ive seen and if they do they copied it from MM) have a reversable top peice that allows for more/less maximum camber. This is what happends when you drop a car, you make it have much more negative camber thus the tire sticks in at the top and pokes out at the bottom.

You can flip the MM plates for more camber and have nearly twice the adjustment, many plates out there wont give you near the adjustment you want so do it right or just live with crappy tire wear.

With that said you are usually ok with around 1 inch of a drop (give or take .2 tenths) so if you are in that range you shouldnt have huge tire wearing issues. Its best to measure your car before and after the drop dont just assume it will drop the amount the say. Do it on a level ground as well, give it a week to settle and measure again and then get the alignment~

The stock setup is pretty much unadjustable FYI you can only tinker with the tie rod ends~ (there are other getto things you can do... but dont)

[ridenmystang]

So glad ya'll know what your talking about... I'd be lost without ya'll

[Danger Dude]

I have had both UPR sharks and now have MM plates. Sharks are good for 1.2 and then they run out of adjustment. I would get the MM C/C plates but the UPR 4 bolts will do the job for about $40 less

[Brent]

I got MM 4 Bolts I need to get in. May do that after class tonight

[STEVE]

www.stangsuspension.com
You can get some of that from them.

[PureVenom]

Originally Posted by Herbstang

Very Nice List !! Your car has come a long way and is looking real good .But how about a SCT chip Support the site sponors

I am with Herby with the SCT...but if you want a programmer, get the SCT XCal 2 instead of the predator. The additional features that come with it beyond the programming capabilities are very much worth it.

[Herbstang]

Originally Posted by Smurfin

I am with Herby with the SCT...but if you want a programmer, get the SCT XCal 2 instead of the predator. The additional features that come with it beyond the programming capabilities are very much worth it.

Listen to Robbie He speaks the truth I'll be upgrading my SCT chip to the new XCAL 2 as soon as I get some time and make the 2 hr ride to VMP

[Thomas91169]

nooooooooo

buy my predator. 200$ shipped!

[ridenmystang]

Anyone ever headr of D&D Motorsports caster camber plates ?

[Brent]

Nope never heard of them

My MM Camber plates were 189 shipped from Stangsuspension.com though

[ridenmystang]

Aww thanks

[bbunt302]

Originally Posted by ridenmystang

Anyone ever headr of D&D Motorsports caster camber plates ?

I've heard of them, but I think you should go ahead and get the MM plates. I personally will not buy a Mustang suspension part from anyone but Maximum Motorsports.

[02silverstang]

i have some slp long tube headers only have 5,000 miles on then put them on 7 months ago motor blew so selling other stuff also have 75 mm acufad throtle body and cnl plenuem.

[ridenmystang]

Sorry I already have all of that but thanks anyways