Hydraulic clutch line - Mustang Evolution

Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 2005-2010 Mustang GT



Reply
 
Thread Tools Search this Thread
Please support our sponsors and let them know you heard about them here!
Old 04-19-2014, 05:01 PM   #1
Registered Member
Regular
 
Mark221's Avatar
 
Join Date: Jan 2013
Location: Cleveland
Region: Ohio
Posts: 105
Hydraulic clutch line

I purchased a SR Performance braided steel hydraulic clutch line from AM. Has anyone changed this. I'm trying to figure out how to get the clips out and I'm not succeeding. Any help would greatly be appreciated. My car is an 05 GT
Mark221 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 04-23-2014, 02:49 PM   #2
Registered Member
Regular
 
Bennyhill's Avatar
 
Join Date: May 2012
Region: Canada
Posts: 275
There is a metal retaining clip holding the clutch line in. Use needle nose pliers or a small screw driver to pop the retaining clip out. Then bam it just slides out.. Now don't loose the clip.. That's why I suggest needle nose, it's a c$&# trying to find one of those clips!
Bennyhill is offline   Reply With Quote
Old 04-23-2014, 05:04 PM   #3
Registered Member
Regular
 
Mark221's Avatar
 
Join Date: Jan 2013
Location: Cleveland
Region: Ohio
Posts: 105
Thanks a lot it seems simple enough but I know it won't be
Mark221 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 04-23-2014, 07:04 PM   #4
Registered Member
Regular
 
Bennyhill's Avatar
 
Join Date: May 2012
Region: Canada
Posts: 275
It really is simple it's just getting the pin started. Small flat head screw driver to start. Grab it with the needle nose pliers wala done!
Bennyhill is offline   Reply With Quote
Old 04-23-2014, 07:19 PM   #5
Registered Member
Regular
 
Mark221's Avatar
 
Join Date: Jan 2013
Location: Cleveland
Region: Ohio
Posts: 105
Do you reuse the plastic fitting with the bleeder?
Mark221 is offline   Reply With Quote
Old 04-23-2014, 07:26 PM   #6
Registered Member
Regular
 
Bennyhill's Avatar
 
Join Date: May 2012
Region: Canada
Posts: 275
What breather? I reused the plastic fittings yes. It's as simple as pulling the old ones out of the plastic fitting installing the new and install the metal retaining clip..
Bennyhill is offline   Reply With Quote
Old 04-23-2014, 07:43 PM   #7
Registered Member
Regular
 
Mark221's Avatar
 
Join Date: Jan 2013
Location: Cleveland
Region: Ohio
Posts: 105
On mine which is an 05 there is a line bleeder on the fitting that goes into the trans
Mark221 is offline   Reply With Quote
Old 04-23-2014, 07:57 PM   #8
Registered Member
Regular
 
Bennyhill's Avatar
 
Join Date: May 2012
Region: Canada
Posts: 275
Hmm I have an 06 and I didn't notice a bleeder when I removed mine.. Hhmm I would say the bleeder gets removed. Unless you can install the new line into the bleeder.. Did you buy your car used?
Bennyhill is offline   Reply With Quote
Old 04-23-2014, 08:03 PM   #9
Registered Member
Regular
 
Mark221's Avatar
 
Join Date: Jan 2013
Location: Cleveland
Region: Ohio
Posts: 105
No bought it new. I know the bleeder was not used in all years but don't know when that was. It's a right angle fitting into the trans and the bleeder points rearward and up at a 45deg ang
Mark221 is offline   Reply With Quote
Old 04-24-2014, 12:41 AM   #10
Registered Member
Regular
 
Silver06GT's Avatar
 
Join Date: Mar 2013
Location: Canton
Region: Michigan
Posts: 78
I had a bleed valve on mine, an 06. But good luck trying to get to it while it's all hooked up, it's impossible!!
Silver06GT is offline   Reply With Quote
Reply

Lower Navigation
Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 2005-2010 Mustang GT

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2013 hydraulic clutch line and fitting retaining clips ddinn25 2011-2014 Mustang GT 1 08-13-2013 07:54 AM
Hydraulic clutch conversion? Fiveohfox 1979-1995 Mustang GT 7 10-06-2012 01:38 AM
Fox Body Hydraulic Clutch Conversion Trojan Horse 1979-1995 Mustang GT 11 08-27-2011 11:43 PM
Hydraulic clutch Snstr99svt 1996-2004 Mustang GT 4 05-07-2011 10:26 AM
Hydraulic clutch?? hadensatb Pre-2005 V6 Mustang 2 02-22-2005 01:24 PM

» Like Us On Facebook



11:35 PM


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0

MustangEvolution.com is in no way associated with or endorsed by Ford Motor Company.