Flywheel Torque - Mustang Evolution

Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 1996-2004 Mustang GT



Reply
 
Thread Tools Search this Thread
Please support our sponsors and let them know you heard about them here!
Old 02-27-2008, 10:10 AM   #1
Registered Member
Regular
 
1234's Avatar
 
Join Date: Feb 2007
Region: Missouri
Posts: 1,292
Flywheel Torque

I bought a lightweight flywheel and a stage 2 clutch for my 03 gt what would be the torque for the flywheel?
__________________
03 GT Charcoal Silver Metallic - Stolen
1234 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 02-27-2008, 11:30 AM   #2
Legacy Member
Legacy
 
Herbstang's Avatar
 
Join Date: Jan 2005
Region: Florida
Posts: 2,932
Re: Flywheel Torque

What brand flywheel ?? Here's some SPEC torque ratings


SPEC Stage 1 Torque Capacity: 410
SPEC Stage 2 Torque Capacity: 520
SPEC Stage 3 Torque Capacity: 680
SPEC Stage 4 Torque Capacity: 680
SPEC Stage 5 Torque Capacity: 1100
__________________

Mods-K&N CAI , True Dual Flowmaster 40, BBK Ceramic Shorties, 3.73 , 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/Dyno Tune

Quote:
"Some people are like Slinkies; useless, but fun to push down the stairs."
Herbstang is offline   Reply With Quote
Old 02-27-2008, 12:28 PM   #3
Legacy Member
Legacy
 
MonteCitan's Avatar
 
Join Date: Aug 2004
Region: California
Posts: 2,506
Send a message via AIM to MonteCitan
Re: Flywheel Torque

Did you mean the torque SPECS for torquing the flywheel on?
__________________
2012 IS F Blue IS F Sport
2006 Mustang V6 wannabe
MonteCitan is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 02-27-2008, 12:35 PM   #4
Registered Member
Regular
 
sledgehammer's Avatar
 
Join Date: Nov 2007
Region: Colorado
Posts: 344
Send a message via Yahoo to sledgehammer
Re: Flywheel Torque

Quote:
Originally Posted by MonteCitan View Post
Did you mean the torque SPECS for torquing the flywheel on?
i think your right... he bought it and needs to put it on so it would make sense
__________________
94 v6 manual, 3.45s w/t-lock, cai, straight straight through dual exhaust, sct eliminator.
sledgehammer is offline   Reply With Quote
Old 02-27-2008, 02:06 PM   #5
Legacy Member
Legacy
 
Herbstang's Avatar
 
Join Date: Jan 2005
Region: Florida
Posts: 2,932
Re: Flywheel Torque

Quote:
Originally Posted by MonteCitan View Post
Did you mean the torque SPECS for torquing the flywheel on?
That was the same thing I thought !! But the question was very fague
__________________

Mods-K&N CAI , True Dual Flowmaster 40, BBK Ceramic Shorties, 3.73 , 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/Dyno Tune

Quote:
"Some people are like Slinkies; useless, but fun to push down the stairs."
Herbstang is offline   Reply With Quote
Old 02-27-2008, 10:41 PM   #6
Registered Member
Regular
 
1234's Avatar
 
Join Date: Feb 2007
Region: Missouri
Posts: 1,292
Re: Flywheel Torque

Sorry for being vague. I meant the torque specs for installing a Fidenza aluminum flywheel?
1234 is offline   Reply With Quote
Old 02-28-2008, 07:04 AM   #7
Legacy Member
Legacy
 
Herbstang's Avatar
 
Join Date: Jan 2005
Region: Florida
Posts: 2,932
Re: Flywheel Torque

Here's some info

Camshafts caps to head 71-106 in/lbs
Camshaft sprocket bolts 82-92 ft/lbs
Cylinder head bolts SOHC (two valve GT and Bullitt)
--Step 1 28-31ft/lbs
--Step 2 Tighten additional 90 degrees
--Step 3 Loosen one full turn
--Step 4 28-31ft/lbs
--Step 5 Tighten additional 90 degrees
--Step 6 Tighten additional 90 degrees
Cylinder head bolts DOHC (four valve Cobra, and Mach One)
--Step 1 28-31ft/lbs
--Step 2 Tighten additional 90 degrees
--Step 3 Tighten additional 90 degrees
Drive belt idler and tensioner bolts 15-22 ft/lbs
Engine compartment brace bolts 15-22 ft/lbs
Engine mount to engine block bolts/studs 25-33 ft/lbs
Engine mount stud to crossmember nuts 95-126 ft/lbs
Exhaust manifold to cylinder head bolts 14-16 ft/lbs
Flywheel moutning bolts 59-64 ft/lbs
Ignition coil brackets to front cover 12-22 ft/lbs
Intake and side plates assembly to cylinder head
--Step 1 15-22 ft/lbs
--Step 2 Tighten additional 90 degrees
Intake manifold to cylinder head bolts
SOHC (two valve GT and bullitt) 15-22 ft/lbs
DOHC (four valve Cobra and Mach One)
Upper plenum to intake 71-106 in/lbs
Intake to lower side plates 71-106 in/lbs
--Step 1 15 ft/lbs
--Step 2 Tighten additional 90 degrees
Oil cooler to filter adapter insert
-1996 59-74 ft/lbs
-1997-later 41-53 ft/lbs
Oil filter adapter bolts 15-22 ft/lbs
Oil pan to engine block bolts
-1996 15-22 ft/lbs
-1997-later
--Step 1 15 ft/lbs
--Step 2 Tighten additional 60 degrees
Oil pick up tube to main bearing cap nut 15-22 ft/lbs
Oil pick up tube to oil pump bolts 71-106 in/lbs
Oil pump to engine block mounting bolts 71-106 in/lbs
Thermostat housing bolts 15-22 ft/lbs
Timing chain cover bolts 15-22 ft/lbs
Timing chain tensioners and guides 15-22 ft/lbs
Valve cover bolts 71-106 in/lbs
Vibration dampner to crankshaft bolt
-1996 114-121 ft/lbs
-1997-later
--Step 1 66 ft/lbs
--Step 2 Loosen one full turn
--Step 3 36 ft/lbs
--Step 4 Tighten additional 90 degrees
Water pump mounting bolts 15-22 ft/lbs
Water pump pulley mounting bolts 15-22 ft/lbs
Wheel lug nuts 85-105 ft/lbs
__________________

Mods-K&N CAI , True Dual Flowmaster 40, BBK Ceramic Shorties, 3.73 , 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/Dyno Tune

Quote:
"Some people are like Slinkies; useless, but fun to push down the stairs."
Herbstang is offline   Reply With Quote
Old 02-28-2008, 07:49 AM   #8
Moderator Emeritus
Legacy
Regular
 
SpectorV's Avatar
 
Join Date: May 2003
Region: Alabama
Posts: 26,049
Send a message via AIM to SpectorV
Re: Flywheel Torque

you best check with the flywheel manuf. to double check they may have different specs if the material (aluminum vs stock) differs.
__________________
2003 Cobra Vert (Redfire) #3938 of 5082 @ 05/27/2003
472rwhp/493rwtq -Modification List - Dyno Sheet
2012 Mustang 3.7L M6 (Kona Blue)
2011 Ford Edge Sport (Red Metallic)
SpectorV is offline   Reply With Quote
Old 02-28-2008, 08:11 AM   #9
Legacy Member
Legacy
 
Herbstang's Avatar
 
Join Date: Jan 2005
Region: Florida
Posts: 2,932
Re: Flywheel Torque

FAQ
__________________

Mods-K&N CAI , True Dual Flowmaster 40, BBK Ceramic Shorties, 3.73 , 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/Dyno Tune

Quote:
"Some people are like Slinkies; useless, but fun to push down the stairs."
Herbstang is offline   Reply With Quote
Old 02-28-2008, 11:06 AM   #10
Registered Member
Regular
 
1234's Avatar
 
Join Date: Feb 2007
Region: Missouri
Posts: 1,292
Re: Flywheel Torque

you guys rock thanks for the help.
1234 is offline   Reply With Quote
Reply

Lower Navigation
Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 1996-2004 Mustang GT

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
flywheel bolts 1996v6stang Pre-2005 V6 Mustang 2 07-12-2010 12:47 PM
Looking for stock V6 flywheel Foxone Pre-2005 V6 Mustang 0 04-07-2010 06:25 PM
Help! Flywheel question. Dsimps 1979-1995 Mustang GT 3 03-10-2008 10:36 PM
looking for a flywheel cjd10 The Bar 2 03-20-2005 05:19 PM
Flywheel questons Tbird232ci Pre-2005 V6 Mustang 3 05-09-2004 10:40 AM

» Like Us On Facebook



12:48 AM


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0

MustangEvolution.com is in no way associated with or endorsed by Ford Motor Company.