N/A coyote Aluminator Build - Mustang Evolution

Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 2011-2014 Mustang GT



Reply
 
Thread Tools Search this Thread
Please support our sponsors and let them know you heard about them here!
Old 01-13-2013, 11:52 PM   #1
Registered Member
Regular
 
kris302's Avatar
 
Join Date: Oct 2012
Region: North Carolina
Posts: 21
N/A coyote Aluminator Build

I signed up just after getting my first s197 chassis a few months ago. However just afterwords the car suffered from a #8 failure. Having bought my car with JLT c/f CAI and tune already in it. Leaving me no way of finding out who tuned it. Furthermore, Ford rejected a warranty claim. So left to my own devices and with my car sitting for a few months now, I have finally ordered my new motor and some go fast goodies for her.

FRPM6007A50NA-00 5.0 Coyote Aluminator N/A
SPEC stage 2 Clutch
SPEC Aluminum Flywheel
Boss Intake Manifold
Steeda Boss Specfic CAI
Kooks Long Tube Headers
Kooks High Flow cats and x pipe
Heartthrob 3" over axle pipes
Kooks Axle Back
Steeda Tri-ax Shifter

Pro-Dyno in Fort Mill SC is doing my install and Tune. i'll be spinning it to 7300 or so. the stock heads and cams dont offer anything out of more revs than that from what i have seen. I expecting around 460-470 on the rollers of his DynoJet. (i believe its a 224 model judging by the small rollers)

ill keep up with the build over the next couple weeks. hoping i can get an aluminum drive shaft and 90mm throttle body before she hits the rollers. only time will tell.
kris302 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 01-14-2013, 12:32 AM   #2
Registered Member
Regular
 
nhcowboy's Avatar
 
Join Date: Jun 2011
Location: Houston
Region: Texas
Posts: 1,171
Quote:
Originally Posted by kris302 View Post
I signed up just after getting my first s197 chassis a few months ago. However just afterwords the car suffered from a #8 failure. Having bought my car with JLT c/f CAI and tune already in it. Leaving me no way of finding out who tuned it. Furthermore, Ford rejected a warranty claim. So left to my own devices and with my car sitting for a few months now, I have finally ordered my new motor and some go fast goodies for her.

FRPM6007A50NA-00 5.0 Coyote Aluminator N/A
SPEC stage 2 Clutch
SPEC Aluminum Flywheel
Boss Intake Manifold
Steeda Boss Specfic CAI
Kooks Long Tube Headers
Kooks High Flow cats and x pipe
Heartthrob 3" over axle pipes
Kooks Axle Back
Steeda Tri-ax Shifter

Pro-Dyno in Fort Mill SC is doing my install and Tune. i'll be spinning it to 7300 or so. the stock heads and cams dont offer anything out of more revs than that from what i have seen. I expecting around 460-470 on the rollers of his DynoJet. (i believe its a 224 model judging by the small rollers)

ill keep up with the build over the next couple weeks. hoping i can get an aluminum drive shaft and 90mm throttle body before she hits the rollers. only time will tell.
That is awesome... Going to be bullet proof.


Curious, since your dropping all that money for an aluminator, did you consider the F/I version and think about adding a supercharger or turbo while you are doing this? It's only money!!!
__________________

2011 Black Mustang GT Premium
Corsa XO & Sport AB/Airaid/Bama 93R
Best 1/4 mile to date 60' 2.009
12.538 ET @112.33
100+ Deg 85 Hum RPR 3PM 1/2 tank street tires
nhcowboy is offline   Reply With Quote
Old 01-14-2013, 01:04 AM   #3
Registered Member
Regular
 
kris302's Avatar
 
Join Date: Oct 2012
Region: North Carolina
Posts: 21
i plan on a single turbo set up the time next year. i'll running 8-9psi. with the low boost the higher compression will keep my throttle response snappy and help the turbo spool faster. and with that i will still be able to run 93 without an issue. the lower static compression just give you more wiggle room with your timing and fueling strategies. as little boost as i will be running it will still be bullet proof.
kris302 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 01-14-2013, 03:49 PM   #4
The Blue Dragon
Regular
Supporter
 
GrabberBlue5.0's Avatar
 
Join Date: Feb 2012
Location: Louisville
Region: Kentucky
Posts: 5,661
This thread should be great! Keep us updated!
__________________
New quick exhaust video

AUGUST 2012 MOTM!!!!
GrabberBlue5.0 is offline   Reply With Quote
Reply

Lower Navigation
Go Back   Mustang Evolution > 1979-2015 Mustang GT || Tech and Talk > 2011-2014 Mustang GT

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are Off


» Like Us On Facebook



05:57 AM


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0

MustangEvolution.com is in no way associated with or endorsed by Ford Motor Company.