Mustang Evolution

Mustang Evolution (http://www.mustangevolution.com/forum/)
-   Pictures and Videos (http://www.mustangevolution.com/forum/f168/)
-   -   Got some work done on Chris' 84 iffy on 56k (http://www.mustangevolution.com/forum/f168/t20106/)

SrATEX 03-18-2006 06:04 PM

Got some work done on Chris' 84 iffy on 56k
 
Well got a later start then we wanted to. Had to go to Wilson Lumber to get some sheet metal (I didnt realize a lumber store sold metal), Orielly's for some stuff, and Harbor Freight for a ton of ****. By the time we did that, got some food, stopped by his dad's house for the compressor it was already 1, so late start. about 4 hours of work and we got a lot done actually. It is almost ready for the bedliner.

the 4" rough country lift with new springs came in on Wed. we ordered it Saturday. fast shipping like when i ordered mine.
http://www.supermotors.org/getfile/3...ideo%20148.jpg
yes the jackstand that we smashed with my bronco is still in the yard :brownbag

being an Alabama truck, rust usually aint a big problem, but the 84 has a bit. this is the worst spot
http://www.supermotors.org/getfile/3...ideo%20149.jpg
this is all just surface...no holes
http://www.supermotors.org/getfile/3...ideo%20150.jpg
thats all for rust really. not bad. we got some metal to weld up and patch it. 20"x50ft roll of it cause that was all they sold...30 bucks not bad for galvanized.

in true redneck fashion...got a back seat for a lawn chair now
http://www.supermotors.org/getfile/3...ideo%20151.jpg
Chris working on the pass seat...notice panels are out too. top will probably come off to make more room to work
http://www.supermotors.org/getfile/3...ideo%20152.jpg
now after taking out the back two bolts for him, taking the above pic, and smoking a cigarette, i got the drivers seat out and he is still on the one bolt...
http://www.supermotors.org/getfile/3...ideo%20153.jpg
all the seats, internal tire carrier, side panels, botom parts of the seat belts, and crappy *** broke spearker are out
http://www.supermotors.org/getfile/3...ideo%20154.jpg
me going at the rust...nice little hole now. i more or less just cut it out
http://www.supermotors.org/getfile/3...ideo%20157.jpg
Chris going at the other side
http://www.supermotors.org/getfile/3...ideo%20159.jpg
this is how we left it
http://www.supermotors.org/getfile/3...ideo%20160.jpg

to finish getting ready for bedlining, need to do a bit more sanding, patch the hole, use some air to spray it out, probably use some mean green on some of that left over carpet glue (that **** is nasty), then vacuum it out and it will be ready.

but i think we got a lot done today. we got hung up on the rear seat bolt that holds the spring down on the right side...had to cut off the bolt head and drill it out. that took us about an hours worth of time...damn dull bits. cant hear much right now...didnt think about my ear defenders until after about an hour of sanding and grinding. but tomorrow is a new day so we should hopefully get a lot more done. maybe get it completely ready for spraying the liner in..especially since we will have a 3rd hand. Dana's best friend and her boyfriend will be here tonight. since they have a wedding shower to go to, we gotta keep her boyfriend company...putting his *** to work, since he is staying with us for free. :histerica

fast64 03-19-2006 05:16 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
nice work so far, can't wait to see it sprayed w/ liner.

lowflyn 03-19-2006 06:47 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
Yeh, any new updates on this project after today?

bbunt302 03-19-2006 08:10 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
Looks like a fun project. Sorry if this has already been mentioned (I'm sure it has and I just missed it), but what are the plans for it?

I assume it will be an offroad vehicle, but what all exactly is he planning on?

SrATEX 03-20-2006 07:50 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
yeah got an update from saturday...have guests at the house so ive not been on the computer much.

We have the inside bedlined now. gonna have to do some touch ups most likely. This weekend we wont have time to work on it with the wedding and all. so it will be pushed of till the weekend after. hopefully that is when we will start the lift.

these are the pics from Sunday. there are a few more, but they are more random then anything
Getting ready to patch the hole in the back
http://www.supermotors.org/getfile/3...ideo%20161.jpg
Chris trying his hand at some welding
http://www.supermotors.org/getfile/3...ideo%20162.jpg
me screwing around with my new mask
http://www.supermotors.org/getfile/3...ideo%20163.jpg
got the banner on..RJ is doing some taping off
http://www.supermotors.org/getfile/3...ideo%20166.jpg
I just like how this turned out
http://www.supermotors.org/getfile/3...ideo%20167.jpg
Chris taping
http://www.supermotors.org/getfile/3...ideo%20168.jpg
all taped off and ready to go
http://www.supermotors.org/getfile/3...ideo%20170.jpg
kicked back in the redneck lawn chair
http://www.supermotors.org/getfile/3...ideo%20171.jpg
this is how it looked like on sunday
http://www.supermotors.org/getfile/3...ideo%20172.jpg
damn i felt like a redneck
http://www.supermotors.org/getfile/3...ideo%20173.jpg
we used Dupli-Color
http://www.supermotors.org/getfile/3...ideo%20174.jpg
Chris spraying
http://www.supermotors.org/getfile/3...ideo%20175.jpg
ended up rolling it on since the hose kept clogging up
http://www.supermotors.org/getfile/3...ideo%20176.jpg
and thats all



The plan for it of right now is to have it by the end of july when we go to Uwharrie in NC for a Fullsizebronco.com Dixie Chapter trail ride is to have it with a 4" Rough Country Suspension lift, 36x13.5x15 Super Swamper IROKs, 4.56 gears, bedlined, and a few other misc cosmetic mostly things. Have a lot of rewiring to do to id since the PO ghetto rigged a lot of stuff, and ghetto rigged it bad. activate the new rear window switch and sparks fly type rigging. Big plans for both his and mine...but down the road.

right now we have to get two broncos up and going. Gotta finish my gears and hopefully bedline mine and all the work on his

fast64 03-20-2006 08:37 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
whos wedgewood blue ranger is that in the background? lol

SrATEX 03-21-2006 11:45 AM

Re: Got some work done on Chris' 84 iffy on 56k
 
Quote:

Originally Posted by fast64
whos wedgewood blue ranger is that in the background? lol

my buddy RJ's

fast64 03-21-2006 02:48 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
Quote:

Originally Posted by SrATEX
my buddy RJ's

well, he's got a nice truck, lol

sonic04edge 03-22-2006 12:17 AM

Re: Got some work done on Chris' 84 iffy on 56k
 
Truck is looking good. Guess I know who to goto when I get the broncoII down here and need something done to it haha.

SrATEX 03-22-2006 05:15 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
yeah sonic i told you Red Clay offroad has your back. PM for my number or get it from Brent

sonic04edge 03-22-2006 10:28 PM

Re: Got some work done on Chris' 84 iffy on 56k
 
Quote:

Originally Posted by SrATEX
yeah sonic i told you Red Clay offroad has your back. PM for my number or get it from Brent

I have it from a previous PM you sent me :good:

SrATEX 03-23-2006 10:18 AM

Re: Got some work done on Chris' 84 iffy on 56k
 
well good then


06:15 PM

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.