Nice list of Engine Parts for V6 Mustangs: Heads, Cams, Intakes...

**Brent** · 12-23-2005, 08:14 PM

Well I am selling my car and the parts I bought to put in it have to go too. Here is what I got and what I want for them:

Engine Block from 96 Mustang bored .030 over and decked with new camshaft bearings - Spoken for
4.2L Crankshaft & Harmonic Balancer - Spoken for
Stage 3 Single Port heads with 3 angle valve job w/ .600 lift springs and head bolts/gaskets - 550 Dollars
Stage 3 Lower Intake w/ gasket - 200 dollars
Stage 3 Upper Intake Cut & Weld w/ gasket - 250 dollars
224/230 Camshaft with new pushrods and shims - 175 dollars
6 Ross Racing Forged Pistons 10:1 Compression ratio with pins and rings - 525 dollars
6 Eagle I-Beam Connecting Rods with new rod bearings - 200 dollars
Aluminum Flywheel - make offer
6 19# fuel injectors - make offer
Timing chain set - Make Offer

**Brent** · 12-23-2005, 08:26 PM

added more

dark · 12-23-2005, 10:15 PM

Kiljosh · 12-24-2005, 02:17 AM

Ill get back to you on the upper, and what size throttle body is it port matched for.

**Brent** · 12-27-2005, 05:55 PM


Quote: Originally Posted by Kiljosh Ill get back to you on the upper, and what size throttle body is it port matched for.

56 I believe

I am holding off on selling anything right now, I am trying to sell the car and parts together. I will get back to everyone that requested parts on this

DocThomasFMF · 12-30-2005, 03:16 PM


Quote: Originally Posted by Brent 56 I believe I am holding off on selling anything right now, I am trying to sell the car and parts together. I will get back to everyone that requested parts on this

Is this stuff from supersix motorsports? How much horse power is the kit good for? How much would you sell all of it for?

dark · 12-30-2005, 03:49 PM

^it's from www.rpm-mustangs.com actually. comparable to ssm

Kiljosh · 12-30-2005, 06:04 PM

Just not as pricey and same quality if you ask me.

RGR · 01-07-2006, 12:44 PM


Quote: Originally Posted by Kiljosh Just not as pricey and same quality if you ask me.

Flow is pretty much the same, I like Mik's exhaust porting, cams and pistons better.
That being said, Tom @ SSM puts out a fine product as well. Just depends on who has
the best setup for your needs. Buying used stuff means big savings but getting a combo
designed for someone else... Mik's combo's are mostly all custom built for each person
so make sure it will work for you!

I can help a potential buyer figure this out. If you do not like the cam I will
spec out a replacement for the buyer as a favor to Brent

evildead · 01-09-2006, 12:52 AM

If still for sale and will work in my 02 3.8. Send pics and quote for all..
thanks jbushway@isp2k.com

**Brent** · 01-09-2006, 03:00 AM

I am waiting for feedback from someone right now. I will keep this thread updated

RGR · 06:14 AM


Quote: Originally Posted by evildead If still for sale and will work in my 02 3.8. Send pics and quote for all.. thanks jbushway@isp2k.com

The only parts that work for you is the crank kit...
crank, pistons, rods, balancer. The cam is too big,
unless you get the intake wildly ported and/or a
custom upper intake to match the cam.

Kiljosh · 04-10-2006, 11:17 PM

Brent, is this stuff still for sale. I need a bottom end lol.

Id be interested in the block, pistons, rods, and crank.

**Brent** · 04-19-2006, 04:06 PM

Nah its not sorry.

**SpectorV** · 04-19-2006, 04:12 PM

hold on now Brent... we may can strike a deal with him for a crank... its a special version that oblong in design you'll love it.

**Brent** · 04-19-2006, 04:27 PM

Wanna know what's funny? The crank is probably perfectly fine

RGR · 04-19-2006, 07:27 PM


Quote: Originally Posted by Kiljosh Brent, is this stuff still for sale. I need a bottom end lol. Id be interested in the block, pistons, rods, and crank.

Still got that crank and pistons... any rods from 96-04 will fit.

lowflyn · 04-19-2006, 07:34 PM

Is the block machined bad now? Crap..that shop really did you bad man.