List your setup's and HP numbers!

[Zim]

Just curious what everyone out there is running.

Personally Im running Cobra intakes, ported gt40s, 1.7 cobra rockers, a9l/pih swap, e303 cam, bbk 70mm TB, pro-m 75mm maf, UD pullies, CAI, shorties, o/r H, mac catback and timings set at 13-14*. Untuned I put down 278rwhp and 308tq. I havnt run it at the track, so I dont know my times.

Id like to get about 6-8lbs of boost on it, then tune it and hope for somewhere around 380-400 rwhp by the end of the summer

[Justin]

donno my hp numbers but i got
Shorty Headers, Cat less Flowmaster Exhaust, Valve Body Shift Kit and K & N Filter

[bbunt302]

AFR 165 Heads, Edelbrock Performer Intake, Comp Xtreme Energy 270HR cam, 30# injectors, Accufab 70mm TB, Pro-M 77mm MAF, U/D crank pulley, Mac shorty headers, Mac Pro-Chamber, Flowmaster American Thunder catback, timing at 18*, DCC Electric Fan, still un-tuned...

Don't have any numbers on it. But it has ran a 8.40 in the 1/8th mile while consistently trapping 87-88mph. Traction was a serious issue...

I'm guessing a little under 300 at the wheels as it sits. Probably would make 310-320 with a tune. That's just an estimate based on current trap speed and how rich I know it's running.

[12second5.0]

Quote: Originally Posted by bbunt302 AFR 165 Heads, Edelbrock Performer Intake, Comp Xtreme Energy 270HR cam, 30# injectors, Accufab 70mm TB, Pro-M 77mm MAF, U/D crank pulley, Mac shorty headers, Mac Pro-Chamber, Flowmaster American Thunder catback, timing at 18*, DCC Electric Fan, still un-tuned... Don't have any numbers on it. But it has ran a 8.40 in the 1/8th mile while consistently trapping 87-88mph. Traction was a serious issue... I'm guessing a little under 300 at the wheels as it sits. Probably would make 310-320 with a tune. That's just an estimate based on current trap speed and how rich I know it's running.

You are over 300 easily.

[12second5.0]

Here's mine........

302
factory rods with ARP rod bolts,stock crank,stock pistons,block decked with pistons .018 above deck,o-ringed deck,FRPP windage tray,Edelbrock Performer5.0 heads,FRPP roller rockers 1.6's,BBK ceramic long tubes,BBK X pipe,American thunder catback,Cobra intake(upper and lower fully ported) BBK 70mm throttle body,ProM 75 Bullit Mass air,42 lb injectors,255lph in tank,FRPP F303 cam,Mike Murillo dyno tune with SCT chip., SQ trim,3.15 upper pulley and a UPR power pipe.

Final dyno numbers are 487rwhp and 466 rwtorque

[timpryor]

don't forget the passenger diaper mod larry

[12second5.0]

Quote: Originally Posted by timpryor don't forget the passenger diaper mod larry

I thought I smelled something funny when I gave you a ride.

[Bane-]

uh 227hp and 305ft lbs (both at flexplate)

stock 5.0 with bbk cai, 70mm maf and flows OH YEA! T5 going in at the end of may, then I can start modding it

[MarkuzLS1]

317hp/328ft-lbs to the wheels. Air-lid and cat-back.

(since I don't have my own section, I'm jumping in here with the rest of you awesome pushrod guys)

[SpectorV]

ive got push rods! (in the floor in my garage )

[damighty5.0]

Ceramic BBK shorties, BBK h-pipe w/cats, Flowmaster American Thunder Mufflers, Accel Ignition coil, BBK underhood intake mated to Moroso Fenderwell Intake, 3.90 gears, rebuilt&built AOD, Tranny cooler, Ford Racing Upper Control Arms, Strut tower brace, custom floor pan supports, EDELBROCK victor series water pump,Hi-miller hoses, Walbro 190lph fuel pump, 225/55/zr16 Goodyear Eagle RSA'S but will be Getting Yokohamas next! Newer struts and front control arms,tierods....

[damighty5.0]

Also better than stock converter of undisclosed proportion

[01mineralgrey6]

Right now... Drop in K&N no silencer, Spintech sideexit catback.
Used to have JLT intake, accufab 70mmTB& Plenum, UPR o/r X, Magnapacks,SCT chip. Don't know the power output, but it scooted along fine