12.41 @ 109.35 N/A Auto New Best

[2K05GT]

We attended the GOOTC (Get out of the Cold) event by Bad Mustang Club at Maryland International Raceway..
I ran My Best time today

60' - 1.845
330 - 5.158
1/8 - 7.936
MPH - 87.91
1000 - 10.357
1/4 - 12.415
MPH - 109.35





4.6L 281 V8 3V Mod Motor.....
JLT II CAI 93 Tune (BamaChips)
Spyder Aluminum DS
Steeda UDP
Steeda CMDP
FRPP 4.10 Gears
CHE Lower Control Arms
JBA LT headers
JBA catted H-Pipe
MAC Axle Back Mufflers

Stock 5R55S Automatic Tranny.
BFG 275/40 17 Drag Radials mounted on Stock GT Rims
3575 Race weight w/ Driver

[wiarumas]

nice

[05RedDevil]

You bastard. I wanted to go to that event but couldn't make it. Now I'm real jealous.

[Brent]

Very nice times

[2K05GT]

Quote: Originally Posted by 05RedDevil You bastard. I wanted to go to that event but couldn't make it. Now I'm real jealous.

Dude, You should have, I don't mean to rub it in but Damn it was a nice day,
45 Deg Low Humidity with a D/A of -1400 we were running great times, I got 5 runs in by 4 and there were almost 200 Mustangs alone, They even gave us our own session or we could run in the normal ones.

[Herbstang]

Sweet !!

[05RedDevil]

My car is getting shipped to Brenspeed and it was supposed to get picked up last week but, as it ends up, it won't get picked up until tomorrow. The good news is that it will come back with some nasty power (because of new UDP's, TB, Delete Plates, Camshafts, Aluminum Driveshaft) and a dyno form to prove it. If I had known I would have had the car over the weekend then I would have gone to GOOTC.

[2K05GT]

Quote: Originally Posted by 05RedDevil My car is getting shipped to Brenspeed and it was supposed to get picked up last week but, as it ends up, it won't get picked up until tomorrow. The good news is that it will come back with some nasty power (because of new UDP's, TB, Delete Plates, Camshafts, Aluminum Driveshaft) and a dyno form to prove it. If I had known I would have had the car over the weekend then I would have gone to GOOTC.

Did you have Brent Install the Cams? or was it just for a tune?

If just a tune I have asked Doug From Bama Chips to come and do a Dyno Tunning session in the DC Area, he is working out the Dyno Rental fees at the local shop. you could have drove down for that, unless you only like Brendspeed. then it does not matter LOL ...
Good Luck, I would love to see your car run with those Cams..

[MonteCitan]

damn 12.4 with typical boltons... makes me wonder why I spent so much on the 92.. oh yeah, I'm still waiting for boost, d'oh


nice times!

[05RedDevil]

The install hasnt taken place yet, like I said, the car will be shipped out tomorrow morning. Yeah, Brent is going to install the cams, pulleys, aluminum driveshaft, delete plates, and throttle body as well as dyno and tune the car. It is a lot of work they are doing and it is actually cheaper to have it shipped to them than to drive it to any place i have called in NY, NJ or MD. Plus I have full faith and trust in the guys at Brenspeed. Some places I decided against just by my phone convo with them and was surprised by their lack of knowledge.
Maybe one day I too will be running in the 12's