Welcome to Mustang Evolution.
|
  |
|
|
|
07-24-2008, 03:14 AM
|
#1
|
|
  |
|
1966 Mustang - rear seat belt mountings
|
|
The Open Road
Join Date: Jun 2008
City: Warwick
State: Europe
Posts: 10
|
I have a 66 Mustang Fastback which has front lap belts fitted.
As our car goes out on hire by families I am keen to install seat belts in the back as well for obvious safety reasons.
There are small slots in the corner of the rear seat as if to allow seat belts through the cushion. Does anyone know if there are seat belt mountings already fitted to the bodywork of a 66 Mustang? |
|
|
|
|
07-24-2008, 07:20 AM
|
#2
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Human Mamogram
Join Date: May 2008
City: Baton Rouge
State: Louisiana
Posts: 1,760
|
i think there are bolt holes in the floor, for some reason i remember them being there last time i changed a set of floorpans.
__________________
2002 GT,T56,99 cobra aluminum block, Eagle rods,Mahle coated pistons,04 cobra crank,04 cobra heads/cams,UPR tubular K-member kit,full UPR solid race rear suspension,NOS direct port wet kit,fidanza flywheel, spec2+ clutch,motorsport 4:10s,full Hearthrob exhaust.(pretty much stock)
|
|
|
|
|
|
07-24-2008, 08:15 AM
|
#3
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
The Open Road
Join Date: Jun 2008
City: Warwick
State: Europe
Posts: 10
|
Thanks, I'll check it out when I get a chance. |
|
|
|
|
|
07-24-2008, 02:22 PM
|
#4
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Deranged
Join Date: Jan 2005
City: Largo
State: Florida
Posts: 6,290
|
__________________
Mods-MAc CAI , True Dual Flowmaster 40,3.73 ,T-Lok, 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/ Tune
Last edited by Herbstang; 07-24-2008 at 02:26 PM.
|
|
|
|
|
|
07-24-2008, 02:43 PM
|
#5
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Deranged
Join Date: Jan 2005
City: Largo
State: Florida
Posts: 6,290
|
__________________
Mods-MAc CAI , True Dual Flowmaster 40,3.73 ,T-Lok, 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/ Tune
|
|
|
|
|
|
07-24-2008, 02:59 PM
|
#6
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Human Mamogram
Join Date: May 2008
City: Baton Rouge
State: Louisiana
Posts: 1,760
|
they must be a standard option on replacement pans, im pretty sure the last set i installed had holes in them.
__________________
2002 GT,T56,99 cobra aluminum block, Eagle rods,Mahle coated pistons,04 cobra crank,04 cobra heads/cams,UPR tubular K-member kit,full UPR solid race rear suspension,NOS direct port wet kit,fidanza flywheel, spec2+ clutch,motorsport 4:10s,full Hearthrob exhaust.(pretty much stock)
|
|
|
|
|
|
07-25-2008, 07:06 AM
|
#7
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Deranged
Join Date: Jan 2005
City: Largo
State: Florida
Posts: 6,290
|
You are correct !!!! I believe rear belts came standard starting in 67
__________________
Mods-MAc CAI , True Dual Flowmaster 40,3.73 ,T-Lok, 25% UDP, 3/8 Phenolic Intake Spacer ,Steeda Tri-ax, SCT Chip/ Tune
|
|
|
|
|
|
08-17-2008, 02:24 PM
|
#8
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
Registered User
Join Date: Aug 2008
City: Pittsburgh
State: Pennsylvania
Posts: 4
|
Then my mustang must have gotten them as options. My 66 has never had its floor pans replaced, but when we replaced the old belts we found that there where four sets of belts in the parts box in the trunk. the holes for mine were in the floor pan, just under the large opening between the rear back seat cushion and trunk. The 2 inner holes are just to the left and right of the transmission hump, and the outer holes where pretty much right behind the back corners of the bottom cushion. But you said yours was a fastback, and mine is the coupe/notchback. But still, I hope this helps.
__________________
Verloren ist nur, wer sich selbst aufgibt. ("Lost are only those who abandon themselves.")--my great, great uncle Hans-Ulrich Rudel
|
|
|
|
|
|
08-17-2008, 04:03 PM
|
#9
|
|
|
|
Re: 1966 Mustang - rear seat belt mountings
|
|
The Open Road
Join Date: Jun 2008
City: Warwick
State: Europe
Posts: 10
|
I still haven't had time to look, but that makes me think it is definitely worth checking out.
I'll lt you all know what I find.
Thanks. |
|
|
|
|
|
