[scott_anderson]

So, i work in a workshop that mostly works on 2005+ mustangs. And i like to think i know my way around mustangs as a whole. However. I own a 95 gt and live in dubai. So information is rare on such a car.

A.) Best CAI? Im leaning towards BBK's but am open to any suggestions.

B.) I hear the best way to make power on these cars is to change the stock cast iron ones. True? If so what heads?

C.) Anyone know of any websites where i could buy stock black interiors? Summit, AM etc cant seem to help.

Cheers guys. Any suggestions/help is much appreciated.

Scot.

 

[keaton5.0]

Bbk cai is good. Heads depend on how much power your shooting for and what the car is going to be used for. Strip car? Street car? Little bit of both?

 

[scott_anderson]

Car will be used as a street car. Aiming for 400-450 mark.
Any other options except the bbk?

 

[keaton5.0]

Car will be used as a street car. Aiming for 400-450 mark.
Any other options except the bbk?

Only cai iv used is the bbk. bbk is good stuff. 400+ will be difficult on a naturally aspirated 302 especially if you want 400hp at the wheels. 400 at the crank could be done fairly easily by stroking the 302 to a 331. Do a little research on trickflow twisted wedge heads and AFR heads. Im personally looking at the trickflow 170 heads. The design lets them flow like a 185cc head with a shorter runner and can be ported for even more air flow. Once you decide on a set of heads then you can start looking at intakes and cams to match them.

 

[WhiteCobra94]

The best cai IMO is JLT's

 

[Slp_loudmouth]

The best cai IMO is JLT's

I have the new JLT in my 02. In love with it I can hear the air suck in when I step on it

 

[scott_anderson]

Theres a JLT for the '95 GT?

 

[WhiteCobra94]

Theres a JLT for the '95 GT?

Yes !

http://www.jpcracing.com/jlt-true-cold-air-intake-kit-1994-95-5-0-mustang/

 

[Finchms]

So, i work in a workshop that mostly works on 2005+ mustangs. And i like to think i know my way around mustangs as a whole. However. I own a 95 gt and live in dubai. So information is rare on such a car.

A.) Best CAI? Im leaning towards BBK's but am open to any suggestions.

B.) I hear the best way to make power on these cars is to change the stock cast iron ones. True? If so what heads?

C.) Anyone know of any websites where i could buy stock black interiors? Summit, AM etc cant seem to help.

Cheers guys. Any suggestions/help is much appreciated.

Scot.

Check cj pony parts. I think they have the black interior.

 

[mustangmania91]

On your interior, CJ PONY PARTS and Late Model Restoration have the most up to date options. Depending on package size usually all ship free. I have and will continue to buy parts from both.

 

[Finchms]

On your interior, CJ PONY PARTS and Late Model Restoration have the most up to date options. Depending on package size usually all ship free. I have and will continue to buy parts from both.

+1 on ltr. I had a brain fart earlier n couldn't think of it. Lol

 

[scott_anderson]

On your interior, CJ PONY PARTS and Late Model Restoration have the most up to date options. Depending on package size usually all ship free. I have and will continue to buy parts from both.

I havent seen anything on late model. Will check out CJ

 

[scott_anderson]

Only cai iv used is the bbk. bbk is good stuff. 400+ will be difficult on a naturally aspirated 302 especially if you want 400hp at the wheels. 400 at the crank could be done fairly easily by stroking the 302 to a 331. Do a little research on trickflow twisted wedge heads and AFR heads. Im personally looking at the trickflow 170 heads. The design lets them flow like a 185cc head with a shorter runner and can be ported for even more air flow. Once you decide on a set of heads then you can start looking at intakes and cams to match them.

Ive heard some great things about trickflows wedge heads. I think my plan at the minute is to do the basics. CAI, UDP etc. First big step would be to convert to a manual trans. (Is it the T-51? Rings a bell but cant say i remember the model number). Then im thinking of stroking it, balancing the crank etc.Then ill get to heads. Trickflows just seem to stand out by a mile.
With regards to cams. All i can find is fords 303 series. Dosent bother me. I like the B303. Just means id need to change my rockers to 1.7 not the stock 1.6 and get some new pushrods. Out of curiosity though. Are there any cams where i can stick to a 1.6? Im after the rough idle, bit of street performance but nothing too 'over the edge'

 

[mustangmania91]

E303 from ford racing is a mild cam. Works well and sounds mean. I had a ford mustang mechanic (only does work on foxbody mustangs) tell me that a direct bolt on head with good HP gains is the AFR heads. U can find them in LMR catalogs. He personally said he wouod put that head up against most others any day. Just a suggestion though

 

[scott_anderson]

E303 from ford racing is a mild cam. Works well and sounds mean. I had a ford mustang mechanic (only does work on foxbody mustangs) tell me that a direct bolt on head with good HP gains is the AFR heads. U can find them in LMR catalogs. He personally said he wouod put that head up against most others any day. Just a suggestion though

Ill check them out. Cheers for the help. Much appreciated.

 

[WhiteCobra94]

TrickFlow stage 1 cams are great with 1.6 or 1.7

Here's a clip of mine with TFS Stage 1 cam and 1.7 rockers

http://youtu.be/N_7fYMoVpv4

 

[Ewokjax95]

+1 on the afr heads. 400hp is quite a bit on a pushrod 302 but I think with a big lunati cam, upper and lower intake, and the afr 185cc heads, it's doable.

 

[scott_anderson]

TrickFlow stage 1 cams are great with 1.6 or 1.7

Here's a clip of mine with TFS Stage 1 cam and 1.7 rockers

http://youtu.be/N_7fYMoVpv4

Where can i find these trickflow cams?
Love the sound of it.

---------- Post added at 02:48 PM ---------- Previous post was at 02:45 PM ----------

With regards to upper and lower intake manifolds, whats on the market? Im big on cutting down weight and was able to find a polymer upper intake manifold from comp cams. My minds very set on that. But nothing really in sight for the lower manifold.

 

[WhiteCobra94]

Summit Racing has them!

 

[scott_anderson]

Summit Racing has them!

Plastic/lightweight ones? Only seen the upper. Not lower?